RAID Reinstall

RAID reinstallation instructions.

REQUIREMENTS:

1. A USB with 8GB of storage space (32GB Max)

2. A little bit of handiness and a little knowledge about PCs

WHY IS THIS HIGHLY RECOMMEND?

The reason this reinstall method is recommended, especially for people with a lot of HWID bans on their PC, is because this reinstall method changes your disk drive serials too. This is an important factor and almost a 99% successful spoof at the end.

Reminder: This guide is for AMD ONLY, unless you know what your doing on Intel. 💢

HOW TO REINSTALL & SPOOF DISKS (BYPASS DISK BAN)

Follow this video on how to setup Rufus

• Make sure your USB Stick is connected!

Rufus - Create bootable USB drives the easy wayRufus

Download Windows 10

After Rufus is finished and says READY in green click close

[IMPORTANT] AMD RAID FILES: DOWNLOAD RAID FILES <- PUT FILES ON THE USB.

YOUR USB CONTENT SHOULD LOOK LIKE THIS NOW:

NOTE: When reinstalling Windows, most modern systems will automatically detect and install basic Ethernet drivers, so your connection will work fine after the installation. ✅

In some cases, you may need to manually download and install network drivers.

Make sure to download your network drivers (LAN) and/or WiFi drivers from your corresponding motherboard model. So for example "Asus B550 Network drivers" on Google, and put them in the USB drive. You can skip this step since this is just a precaution, but there is a small risk of no connection after Windows reinstall. 🌐

STEP 1: BOOT INTO BIOS

Once completed, and the USB looks like the screenshot above, restart the computer, and boot into bios. How to boot into BIOS: Video tutorial here (simple). ✅

STEP 2: ENABLE RAID MODE IN BIOS

Once in BIOS, follow the steps listed here down below to enable RAID.

ASUS

Asus Tutorial - https://rentry.co/cr6pksfp

ROG Asus Tutorial - https://rog.asus.com/articles/crosshair-motherboards/what-is-raid-setup-guide/

MSI

MSI Tutorial - https://rentry.co/fx3cfqwu

GIGABYTE

Gigabyte Tutorial - https://rentry.co/rttkxn9m

ASROCK

Asrock Intel Tutorial - https://download.asrock.com/Manual/RAID/Z170%20Pro4/English.pdf

Asrock AMD Tutorial - https://download.asrock.com/Manual/RAID/X570S%20PG%20Riptide/English.pdf

STEP 3: BOOT INTO USB AND INSTALL WINDOWS

After you successfully raided your drive save and exit your bios and while your PC is starting spam the F2 or F11 button to get into the boot menu. Once in the boot menu select your USB (UEFI: YOUR USB NAME) and press enter. After that continue with the steps below

Select Windows 10 Pro (IMPORTANT!)

Select "I don't have a product key" (Don't worry, we will activate this later for free)

Select Custom: Install Windows only (advanced)

If you have done everything correctly so far then you will see no drives! (If you do see drives try to select one and try to click next, if it works then something went wrong and you will have to redo). Since you can't install windows now you will need to load the drivers you put on your USB earlier, follow these steps to do it

1. Click "Load driver", then "Browse", then find your USB and expand it by clicking the tiny arrow next to it.

2. Find the folder you put on the USB earlier and in it choose the folder for your disk type (SATA/NVME) and click OK

3. Select the only driver that pops up and click "Next"

4. Do step 1 and 2 again where you select the SATA/NVME folder

5. Select the newly appeared driver (Most likely called Controller) and click "Next"

6. (In case your drive still didn't pop up redo the SATA/NVME folder and load the Controller Driver again)

Select your main drive and click Next

The installation process should start

Make sure to follow these steps while and after reinstalling:

1. Make an offline account or a new Microsoft account. Don't log in to the old ones.

2. Do not log in to OneDrive, Gefore Experience, & Medal using the same account.